Same-day and emergency appointments
Up-front pricing before any work starts
Licensed, insured, background-checked technicians
Written safety report after every visit
Toronto, City of Toronto
Furnace Installation & Replacement in Toronto
Right-sized, correctly vented high-efficiency furnace replacement with a heat-loss calculation.
Most furnaces in Ontario are replaced with whatever size the old one was, which is how homes end up with an oversized unit that short-cycles for twenty years. We run a heat-loss calculation on your actual house before quoting a size.
(647) 000-0000Furnace Installation in Toronto
Send the symptom and your postal code — we'll confirm an arrival window.
Local context
Furnace Installation for Toronto homes
Toronto's older housing stock frequently has a mid-efficiency furnace sharing a masonry chimney with the water heater. Going condensing orphans that water heater, and a properly sized liner has to be part of the quote — not a surprise on install day.
An oversized furnace heats the thermostat quickly and the house unevenly, cycles constantly, wears its igniter and inducer prematurely, and never runs long enough at low fire to be efficient. A correctly sized modulating unit runs longer at lower output and holds temperature far more evenly — the comfort difference is usually more noticeable than the fuel saving.
Replacing a mid-efficiency furnace with a condensing one changes the venting entirely. The new unit vents in plastic through a sidewall, which orphans the water heater on the old masonry chimney and often requires a liner. Quotes that ignore that are quotes that will cost you again later. Ours includes the venting work, the permit and the inspection, and we hand over a commissioning sheet with gas pressure, temperature rise and static pressure recorded.
A replacement is only as good as the load calculation behind it. We size to the house — square footage, insulation, window area, air leakage and the duct system you already have — rather than matching the badge on the old unit. Most furnaces we replace were oversized when installed, and an oversized condensing furnace short-cycles, never reaches steady-state efficiency and wears its ignition components out early. Right-sizing typically means a smaller and quieter unit than the one coming out.
The parts of the job that get skipped by low quotes are the ones that determine whether the installation lasts: a correctly sized return, sealed and supported venting at the right slope, a proper condensate route with neutralisation where required, a new gas connection and shut-off, and commissioning readings recorded at the end. We file the permit, book the inspection and leave you the manufacturer registration completed so the warranty is actually valid.
What the housing stock in Toronto means for this job
Inside the old city you are mostly looking at pre-1940 semis and rowhouses with narrow mechanical rooms, converted gravity ductwork and masonry flues that predate gas. The post-war belt through Etobicoke, North York and Scarborough is bungalows and side-splits on their second or third furnace, and the infill and condo-adjacent stock downtown is high-efficiency and direct-vented from the start. For furnace installation, that matters because the work concentrates on sizing, venting and commissioning — and that is exactly what changes between a Annex property and a newer build in High Park.
Timing in Toronto
Planned replacements are cheapest and easiest to schedule in spring and early autumn; emergency replacements in January cost more and offer far less choice of equipment. Locally, that plays out like this: Downtown sits in the warmest part of the GTA thanks to the lake and the urban heat island, so shoulder-season demand starts later here than it does up north — but the same heat island pushes summer overnight lows up, which is why AC systems in the old city rarely get the night-time recovery they were sized for.
What it costs here
Efficiency tier and staging drive equipment cost; venting changes, duct or return modifications and permit work drive installation cost. Old-city work carries access costs that suburban work does not: permit parking on narrow streets, laneway-only rear access, tight basement stairs that limit equipment size, and third-floor or rooftop terminations that need ladder or lift time.
Permits and jurisdiction
Permits and mechanical inspections for Toronto addresses go through the City of Toronto, gas work is under TSSA province-wide, and electrical connections are inspected by the ESA. We handle the filing rather than leaving it with you.
Call now, or book it in?
Call now
- A cracked heat exchanger confirmed by inspection
- Repeated CO alarm activations
- A furnace over twenty years old that has failed mid-winter
Can be scheduled
- Rising repair frequency on a unit past fifteen years
- Uneven heating that a repair has not solved
- Planning ahead before next heating season
How a Toronto visit runs
- 1Heat-loss calculationRoom-by-room sizing based on your actual insulation, windows and orientation — not the old unit's badge.
- 2Written optionsTwo or three real options with efficiency, sound rating and total installed price. No pressure close.
- 3Venting planSidewall venting, condensate route and what happens to the water heater's flue, all specified before install day.
- 4Install & permitOne-day changeover in most homes, permit filed and inspection arranged.
- 5CommissionGas pressure, temperature rise, static pressure and combustion readings recorded and left with you.
What affects furnace installation pricing in Toronto
- Output capacity and efficiency tier, and whether the blower is single-stage, two-stage or modulating
- Whether the changeover requires new sidewall venting and a chimney liner for the water heater
- Condensate drainage — a basement without a nearby drain needs a condensate pump
- Existing ductwork condition and whether the plenum and return need modification
- Available manufacturer and utility rebates, which we apply for on your behalf
FAQ
Furnace Installation questions from Toronto homeowners
How long does a furnace replacement take?
A straight changeover is a single day. Adding sidewall venting, a chimney liner for the water heater or ductwork modification can extend it to two.
What size furnace do I need?
The only honest answer comes from a heat-loss calculation on your specific home. Matching the old unit's size perpetuates whatever sizing error was made the first time, and in {city} that error is usually oversizing.
Do I need a permit to replace a furnace?
Yes, and we file it. A permitted, inspected install protects your manufacturer warranty and matters at resale.
Are there rebates available?
Manufacturer and utility programs change through the year. We check what is active at the time of your quote and handle the paperwork rather than leaving you to claim it.
What size furnace do homes like mine here usually need?
Inside the old city you are mostly looking at pre-1940 semis and rowhouses with narrow mechanical rooms, converted gravity ductwork and masonry flues that predate gas. The post-war belt through Etobicoke, North York and Scarborough is bungalows and side-splits on their second or third furnace, and the infill and condo-adjacent stock downtown is high-efficiency and direct-vented from the start. On a furnace installation visit in Annex, High Park, Roncesvalles or anywhere else in Toronto, we work from what the house actually is rather than a standard checklist — sizing, venting and commissioning gets assessed on the property, and you get the readings in writing.
When is the best time of year to replace a furnace here?
Planned replacements are cheapest and easiest to schedule in spring and early autumn; emergency replacements in January cost more and offer far less choice of equipment. Downtown sits in the warmest part of the GTA thanks to the lake and the urban heat island, so shoulder-season demand starts later here than it does up north — but the same heat island pushes summer overnight lows up, which is why AC systems in the old city rarely get the night-time recovery they were sized for. We cover Toronto from Annex through Roncesvalles, and also serve 3 neighbouring municipalities, so scheduling outside a demand spike usually means a same-week window.
Pricing
How much does this cost in Toronto?
Typical range is $3,800 – $8,200 installed. Get a number for your own home in about a minute with our instant estimator.
Furnace Installation in Toronto, booked today
Call for the fastest response, or send a request and we'll confirm your arrival window.